Helical Pier Installation
Our rigs drive every helical pier to the torque its engineered design calls for, commonly 10 to 30 feet deep, deeper where Ellis County's soil profile requires it.
Installation details- CALL US TODAY: (817) 402-7113
Engineered helical piers for commercial buildings, new construction, and foundation repair on Ellis County's Blackland Prairie clay. Family-owned since 2005, with our own manufacturing, rigs, and crews.
Waxahachie sits in Ellis County's Blackland Prairie, ground famous for cotton farming and just as well known among foundation engineers for its shrink-swell clay. That clay pulls moisture out from under a slab every summer and takes it back every spring, and a helical pier is built to reach past that movement instead of riding on top of it.
Ellis County's dark clay soil can shrink several inches during a dry Texas summer, then swell right back with the first heavy rain. A helical pier is torqued into soil below where that swing reaches.
From the century-old commercial buildings around the Ellis County Courthouse to new commercial and industrial sites along I-35E and US-287, helical piers carry new construction or retrofit under an existing building without major demolition.
Roof drains that discharge against the foundation, parking lot runoff, and low spots that hold water cause movement that isn't a structural failure at all. Correcting drainage first can lower the pier count a design actually needs.
On an existing building, we survey slab elevations and trace the root cause first. If drainage or normal settlement explains what you're seeing, we'll tell you that instead of quoting piers.
One of these alone rarely proves a foundation problem. Several at once, or one that keeps getting worse, deserves a measured look.
We manufacture the helical piers our own crews install, and we stand behind every job ourselves, not through a subcontractor.
Our rigs drive every helical pier to the torque its engineered design calls for, commonly 10 to 30 feet deep, deeper where Ellis County's soil profile requires it.
Installation details
The same J55 steel, ASTM A572 Grade 50 helical piers our crews install ship direct to engineers and contractors who prefer to install with their own teams.
Manufacturing & sales
Stabilize and lift an existing commercial structure with helical piers engineered around its load and Waxahachie's clay profile.
See the processWe review your plans, engineer's design, or geotechnical report, and test holes are free on approved projects. On an existing building, we survey elevations and trace the root cause before quoting.
When helical piers are the right fix, we engineer pier count, spacing, and depth to your structure's load and Ellis County's soil conditions.
Our own crews and rigs install to that design, tracking torque continuously so capacity is measured at every pier, not estimated.
Every pier's torque reading is logged to its location on your property. Commercial installs carry a 10-year warranty, and every job ships with our Green Tag Guarantee.
Anyone can claim quality. These are the records and methods that back it up on your specific job.
Each helical pier advances to the torque its design requires instead of stopping at a preset depth, since torque reflects that location's actual soil capacity.
Every pier's achieved torque is recorded against its position, the paper trail an engineer, an inspector, or a future owner can check against the design.
Compression tests measure downward capacity; tension tests measure resistance to being pulled up. Both run on hydraulic equipment that records movement under load.
When a structural engineer has produced the design, we build to it. Any field change routes back to that engineer first, never decided on-site.
J55 carbon steelASTM A572 Grade 50ASTM A123 hot-dip galvanizingASTM A780 repair standard
Our crews train through our own Helical Trade School, and our CEO, Bill Vaughan, co-authored Next Day Helicals, the industry's field manual on helical pier installation.
| Criterion | Helical pier | Push pier | Drilled/poured pier |
|---|---|---|---|
| Carries load | Immediately on installation | Depends on structure weight for resistance | After concrete cures |
| Wet-weather clay | Installs in wet ground, no open excavation | Excavation needed; slower in wet clay | Holes can collapse in wet clay |
| Capacity verified by | Installation torque, logged per pier | Driving resistance | Design and inspection of the excavation |
| Depth reached | To torque criterion, not a set number | To refusal against structure weight | To designed depth |
"Big City Capability and Small Town Service! Bill Vaugn and team have the tools and expertise to solve any issues you may have, but the best part is the personal service and open and honest explanation of the entire process. Call FnD Piers, you will be in good hands."
"As business professionals, my husband and I have worked with FnD Piers for years. From its owner to its employees, they are one big family and their customers are part of the family. Over the top attitudes and altitudes. We highly recommend FnD Piers for its professionalism and integrity. The most trusted company in the business."
"FnD Piers is your go-to outfit for all things foundation! This Team is "the real deal.""
"FND Piers does excellent work — professional, efficient, and reliable every time. Their crew knows what they’re doing and gets the job done right. Highly recommend them for any helical pier or foundation work."
Waxahachie anchors Ellis County about 28 miles south of downtown Dallas. We install and sell helical piers across all three Waxahachie zip codes and the surrounding Ellis County communities.
The closest of our service cities to Waxahachie, about 20 miles northwest on similar clay.
Helical piers in Mansfield →North on I-35E, roughly 28 miles toward the Metroplex core.
Helical piers in Grand Prairie →Straight up I-35E from Waxahachie, about 28 miles north.
Helical piers in Dallas →A comparable drive west along US-287, similar soil profile.
Helical piers in Burleson →Send us your plans or tell us about the building. You'll get a written quote, and test holes are free on approved projects.